Should you paint a brick house, and what does it cost in Wollongong?
You can, and done properly it lasts well, but it is a one-way decision: paint does not come off brick cleanly. Painting works when the brickwork is sound and dry, the salts and mould are dealt with first, and the system is a masonry sealer under two coats of exterior acrylic. In NSW, brick exteriors cost about $30 to $55 per square metre to paint in 2026, with raw face brick at the top of that range.
Last checked
Should you paint face brick at all?
Only if you are happy never to see the bare brick again. Haymes puts it plainly: unlike repainting a wall inside the home, removing paint from brick later can be difficult and expensive. Painting makes sense to modernise a dated colour, to tie an extension in with the original brickwork, or to cover brick that has weathered badly. It does not make sense over persistent damp, rising moisture, badly deteriorated mortar or structural cracking, because paint hides those and then fails over them.
There is a middle path for a lot of Illawarra houses: paint the trim, fascias, gutters, windows and any rendered sections, and leave the brick. A 1970s blonde brick house often looks a generation newer with new trim colours alone, and nothing is lost. If the brick itself is the problem, render and texture coating is the other way to change it, and it hides more than paint does.
A note on heritage. Parts of the Illawarra sit in heritage conservation areas, and painting previously unpainted face brick on a listed or contributory building can need council approval. Check with Wollongong, Shellharbour or Kiama council before you commit.
Why does moisture matter so much with brick?
Because brick is porous. It takes in water and lets it back out, and a coating that stops the second half of that cycle traps moisture behind the paint. Haymes's guidance is that problems arise when moisture issues are ignored and a coating goes over damp brickwork. Near the coast the problem is worse: salt-laden air wets the wall more often, and salt in the brick draws moisture in from the air.
The giveaway is efflorescence, the white powdery deposit that forms on brick and mortar. It can be brushed off, but Haymes is clear that it should not simply be painted over, because the salts may signal an ongoing moisture source that needs finding first. Scrub it off dry with a stiff brush, wait through a few weeks of weather, and if it comes back there is water getting into the wall from somewhere: a leaking gutter, a failed damp course, garden beds built up against the brick.
The same goes for new brick. Fresh brickwork and mortar carry a lot of water and alkaline salts, and painting too early is how a job fails in its first year. Let a new wall go through a full wet season before you coat it.
How do you prepare brick for painting?
Clean, dry and sound, in that order. All surfaces need to be free of the dust, salt and mould that stop paint sticking, loose mortar needs repointing, and previously painted brick needs the flaking paint taken back to a firm edge. On the coast, a fresh-water wash to get the salt off is the first job, not an optional one.
- Pressure wash or scrub with a stiff brush and fresh water, then let the wall dry out fully. Brick holds water for days after a wash, longer in the shade.
- Treat mould with a proper mould wash and remove it completely; painting over it just feeds it under the film.
- Brush off efflorescence dry and watch whether it returns before you coat.
- Repoint crumbling mortar joints and fill cracks; let the new mortar cure.
- On previously painted brick, scrape and feather the loose edges. If the house was built before 1970, assume the old paint may contain lead and follow the NSW LeadSmart rules.
- Mask windows, paths and garden beds. Brick soaks up paint and a sprayed or rolled wall throws a lot of it around.
What paint system goes on brick?
A sealer or primer made for masonry, then two coats of a premium exterior acrylic. Both Haymes and Dulux sell the pieces: Haymes recommends an acrylic sealer undercoat for porous masonry and a primer-sealer-undercoat for previously painted brick, with its Solashield range on top, and Dulux's brick guide specifies Weathershield as the topcoat, applied with an 18 mm nap roller for the rough surface. The sealer evens out how much the brick drinks, so the topcoats cover properly and the colour comes out uniform.
Sheen matters on brick. Low sheen hides the unevenness of the mortar joints and old repairs; gloss shows every one. For the Illawarra coast, use the maker's premium exterior range rather than a budget masonry paint, and light colours over dark: a dark painted brick wall facing north or east gets very hot and that shortens the life of any coating. The best time to paint outside here is autumn or spring, and brick in particular needs a dry run of days so the wall is not holding water when it is sealed.
How much does it cost to paint a brick house in Wollongong?
In NSW, brick exterior painting typically costs $30 to $55 per square metre in 2026, on The Quote Yard's figures, which include washing, any mortar repair, a masonry sealer or brick primer and two topcoats. The low end is previously painted brick in reasonable condition; the top end is raw, never-painted face brick that needs the full sealer, prime and two-coat system. A single-storey three-bedroom exterior runs $5,000 to $12,000 and a double-storey $8,000 to $18,000 including scaffolding.
Raw brick costs more than render or painted brick for two reasons: it drinks the first coat, so the job uses more sealer and paint per square metre, and the rough face is slower to roll or needs spraying. Our exterior painting cost page has the full breakdown, and the calculator gives a number for your house size.
| Exterior wall type | Typical rate per m² (NSW, 2026) |
|---|---|
| Brick, previously painted, good condition | From about $30 |
| Brick, raw face brick, full sealer and two coats | Up to about $55 |
| Rendered walls in good condition | $20–$35 |
| Weatherboard, well maintained | $25–$40 |
The Quote Yard, exterior painting cost NSW, published 24 August 2026. Wollongong and regional NSW jobs are usually priced below Sydney equivalents.
How long does painted brick last near the coast?
With a proper sealer-and-two-coats system over dry, clean brick, a long time; the failures you see are almost always preparation failures, not paint failures. Salt is the enemy, so a fresh-water rinse of the walls a couple of times a year does more for the paint than anything else. How often to repaint a house near the sea covers the signs, and the Salt Line shows how exposed your suburb is.
Questions people ask
Is painting brick a good idea?
It can be, if the brickwork is sound and dry and you accept that it is permanent. Fix damp and efflorescence first, use a masonry sealer under two coats of premium exterior acrylic, and check heritage rules if the house is in a conservation area.
Can you paint over efflorescence?
No. Brush it off dry and wait to see if it returns. If it does, there is a moisture source feeding the wall that needs fixing before any coating goes on.
Do you need to seal brick before painting?
Yes. Brick is porous and absorbs unevenly, so a masonry sealer or brick primer goes on first to even out absorption and give the topcoats something to grip. Previously painted brick takes a primer-sealer-undercoat instead.
How much does it cost to paint a brick house in NSW?
About $30 to $55 per square metre of wall in 2026, including washing, sealer and two coats, with raw face brick at the top of the range. A single-storey three-bedroom exterior is roughly $5,000 to $12,000 and a double-storey $8,000 to $18,000 with scaffolding.
What is the alternative to painting brick?
Paint the trim and leave the brick, or render and texture coat the walls, which changes the look more completely and covers more surface faults than paint.